top of page
Helix M FOUR

Helix M FOUR

SKU: M Four
If you like to rev up your front and rear speakers, the M FOUR will be exactly the right "tool" to do so. With generously 100 Watts RMS per channel into both 4 Ohms and 2 Ohms load this amp will heat up your voice coils in no time despite its super-compact dimensions. On the other hand the M FOUR stays totally cool thanks to the highly efficient Class D design topology. 3-channel or 2-channel configurations are possible as well, delivering up to 2 x 200 Watts RMS of clean and undistorted output power.
Needless to say that the M FOUR is equipped with a bunch of intelligent attributes like "start-stop capability" and our proprietary "ADEP" highlevel input so that it easily deals with all installation challenges of modern cars. Finally the extensive audio features will offer a sound quality at its best.

  • Features

    • Small footprint Class D amplifier with high output power of 100 Watts RMS @ 4 and 2 Ohms load
    • Start-Stop capability down to 6V supply voltage
    • Smart highlevel input with ADEP circuit (Advanced Diagnostics Error Protection) and Auto Turn-On function
    • Integrated, active crossover with highpass, lowpass and bandpass
    • “Input mode” switch for flexible input signal routing
    • SMD (Surface Mounted Device) manufacturing technology combines minimum space requirement with maximum reliability
    • Exclusive, extremely compact and clean design with illuminated HELIX-logo and low heat dissipation thanks to extraordinary efficiency

     

    Special features:

    Smart highlevel input
    The latest generation of OE car radios incorporates sophisticated possibilities of diagnosing the connected speakers. If a common amplifier will be hooked up failure messages and loss of specific features (e.g. fader function) quite often appear - but not with the M FOUR.
    The new ADEP circuit (Advanced Diagnostics Error Protection) avoids all these problems without loading the speaker outputs of the OE radio during high volumes unnecessarily.

    Start-Stop capability
    The switched power supply of the HELIX M FOUR assures operation even if the battery’s voltage drops down to 6 Volts during engine crank.

  • Specification

    Output power RMS / max.  
    - @ 4 Ohms 4 x 100 / 200 Watts
    - @ 2 Ohms 4 x 100 / 200 Watts
    - @ 1 Ohm -
    - bridged @ 4 Ohms 2 x 200 / 400 Watts
    - bridged @ 2 Ohms - 
    Max. output power per channel* Up to 135 Watts RMS @ 2 Ohms
    Amplifier technology Class D
    Inputs 4 x RCA / Cinch
    4 x Highlevel speaker input
    1 x Remote In
    Input sensitivity RCA / Cinch 0.5 - 6 Volts
    Highlevel 1.3 - 13 Volts
    Input impedance RCA / Cinch 20 kOhms
    Input impedance highlevel 13 Ohms
    Outputs 4 x Speaker output
    Output voltage RCA / Cinch - 
    Signal converter for digital input - 
    Frequency response 10 Hz - 30,000 Hz
    Bass boost - 
    Highpass 15 Hz - 4,000 Hz adjustable
    Lowpass 40 Hz - 4,000 Hz adjustable
    Bandpass 15 Hz - 4,000 Hz adjustable
    Subsonic - 
    Phase - 
    Slope high- / lowpass 12 dB/Oct.
    Slope subsonic / lowpass - 
    Signal-to-noise ratio digital input - 
    Signal-to-noise ratio analog input 98 dB (A-weighted)
    Distortion (THD) 0.05 %
    Damping factor 100
    Operating voltage 10.5 - 16 Volts (max. 5 sec. down to 6 Volts)
    Idle current 1,100 mA
    Fuse 2 x 30 A Maxi-fuse (APX)
    Additional features Active, adjustable crossover, input mode switch, Start-Stop capability, highlevel input with automatic turn on function and Advanced Diagnostics Error Protection (ADEP)
    Dimensions (H x W x D) 50 x 230 x 154 mm /
    2.00 x 9.06 x 6.06”

  • Delivery Contents

    1 x Amplifier HELIX M FOUR
    1 x Mounting material
    1 x Instruction manual

$600.00Price
bottom of page